1#@!#!123s

22527 1#@!#!123s
: / snap / core22 / 1981 / usr / share / subiquity /
Filename : console-conf-wrapper
back
#!/bin/bash
set -e

trap true HUP INT QUIT TSTP
echo_on () { stty echo; }
trap echo_on EXIT

# agetty only sets ICRNL if it has read the username and seen whether
# it was terminated by CR or NL. We pass -n to agetty so that hasn't
# happened and need to force it on. Yay UNIX!
stty icrnl -echo

if [ -e /run/snapd-recovery-chooser-triggered ]; then
    # make sure the chooser binary is there to avoid getting into an awkward
    # state and locking out the user
    if [ -x /usr/lib/snapd/snap-recovery-chooser ]; then
        # when recovery chooser is invoked it takes over the terminal
        exec /usr/lib/snapd/snap-recovery-chooser
    fi
fi

if [ -e /var/lib/console-conf/complete ]; then
    exit 22
fi

# always prefer to use modeevn if it is available
if [ -e "/var/lib/snapd/modeenv" ]; then
    mode="$(sed -n 's/mode=\([^[:space:]]*\)/\1/p' /var/lib/snapd/modeenv)"
else
    mode="$(sed 's/.*snapd_recovery_mode=\([^[:space:]]*\)[[:space:]].*/\1/' /proc/cmdline)"
fi

if [ "${mode}" = "install" ]; then
    echo "Installing the system, please wait for reboot"
    # XXX: replace with something more user friendly after the beta?
    journalctl -u snapd.service -f
    sleep infinity
fi

if [ "$(snap managed)" = "true" ]; then
    # check if we have extrausers that have no password set
    if grep -qE '^[-a-z0-9+.-_]+:x:' /var/lib/extrausers/passwd && ! grep -qE '^[-a-z0-9+.-_]+:\$[0-9]+\$.*:' /var/lib/extrausers/shadow; then
        tty=$(tty)
        tty=$(echo ${tty#/dev/} | tr '/' '-')
        readargs=()
        filepath="/run/console-conf/login-details-${tty}.txt"
        if [ ! -f ${filepath} ]; then
            mkdir -p /run/console-conf
            set +e
            /usr/share/subiquity/console-conf-write-login-details > ${filepath}.tmp
            rval=$?
            set -e
            # A exit code of 2 from console-conf-write-login-details
            # means there are no scope global IP addresses. It will
            # have printed a message saying that you can't log in
            # until the device gets an IP address so we display that
            # but check every 5 seconds if an ip address has appeared.
            if [ $rval -eq 0 ]; then
                mv ${filepath}.tmp ${filepath}
            elif [ $rval -eq 2 ]; then
                mv ${filepath}.tmp ${filepath}.noip
                filepath=${filepath}.noip
                readargs=(-t 5)
            else
                exit $rval
            fi
        fi
        cat $filepath
        set +e
        while :; do
            read "${readargs[@]}" REPLY
            if [ $? -le 128 ]; then
                # If we didn't time out, re-display everything.
                exit 0
            fi
            if ip addr show | grep -qE "scope global"; then
                # If we timed out, but it appears that we may now have
                # an IP address, re-display everything.
                exit 0
            fi
        done
    else
        touch /var/lib/console-conf/complete
        exit 22
    fi
    exit 0
fi

cat /usr/share/subiquity/console-conf-wait
read REPLY
# start the console-conf routine in snapd to delay any new refreshes, and wait
# for current refreshes to complete, this will print off messages if there are
# on-going refreshes
if snap routine console-conf-start --help >/dev/null 2>/dev/null; then
    snap routine console-conf-start
fi
exec console-conf "$@"